Curbs

The type of curb and its location affect driver behavior patterns, which, in turn, affect the safety and utility of a road or street. Curbs, or curbs and gutters, are used mainly in urban areas. They should be used with caution where design speeds exceed 40 mi/h (64 km/h). Following are various reasons for justifying the use of curbs, or curbs and gutters:

• Where required for drainage

• Where needed for channelization, delineation, control of access, or other means of improving traffic flow and safety

• To control parking where applicable

Types of Curb. There are two general categories of curbs: barrier curbs and mount­able curbs. Barrier curbs are relatively high [6 in (0.15 m) or more] and steep-faced. Mountable curbs are 6 in (0.15 m) or less in height and have flatter, sloping faces so that vehicles can cross them with varying degrees of ease. Figure 2.29 (Ref. 14) shows various curb designs that are commonly used on roadways. Types 1, 3, and 4 are examples of mountable curbs and are used for channelizing traffic, especially in islands and medians. Types 2 and 6 are barrier curbs used along pavement edges in urban areas and are designed to handle drainage more efficiently. Types 7 and 8 are tall barrier curbs designed to provide a more positive traffic barrier than the others. Type 7 is used as an alternate for guiderail in low-speed urban situations.

Position of Curb. Curbs are normally used at the edge of pavement on urban streets where the design speed is 40 mi/h (64 km/h) or less. Curbs at the edge of pavement have an effect on the lateral placement of moving vehicles. Drivers tend to shy away from them. Therefore, all curbs should be offset at least 1 ft (0.3 m) and preferably 2 ft (0.6 m) from the edge of the traffic lane. Where curb and gutter are used, the standard gutter width is 2 ft (0.6 m).

On roads where the design speed exceeds 40 mi/h (64 km/h), curbs should be used only in special cases. Special cases may include, but are not limited to, the use of curb to control surface drainage or to reduce right-of-way requirements in restricted areas.

Edge of groded shoulder Portion of volley In depressed aiedl<

‘-B

Treoted Shoulder

СгомоV#r povement Slope t as mo In По* profile.

SECTION Д-Д

Dimensions Applicable toVarying Median Demands M, ft D, in R-l, ft R-2, ft 84 17.25 24.87 55.20 60 11.50 16.31 35.24 50 9.13 12.73 26.93 40 6.75 9.16 18.61

0.04

0.04

Tv-Ospresslon

ДВДЕ

J

SECTION B-B

FIGURE 2.28 Design for U-turn median opening. Conversion: 1 ft = 0.305 m. (From Location and Design Manual, Vol. 1, Roadway Design, Ohio Department of Transportation, with permission)

‘Asphalt’concrete [ Base J
TYPE /
• Bull Joints shell be provided between combined cu/b-and-guller and new rigid pavements. with lit bars or hoot bolts provided at five foot Intervals. Combined curb-ond-gutter shell be tied to existing rigid pavements wllh expansion hoot bolls spaced at five foot Intorvols. if the combined curb-ond-gulfer adjoins a new rigid base or on existing rigid base or povemeni that Is to be surfoced with bituminous malerlol. a bull Jolnl shall be provided and tie bars.’hoot bolls or expansion hoot bolls shall be omitted.
TYPE 5
TYPE 2	TYPE 4

When it is necessary to use curbs on roads where the design speed is over 40 mi/h, they should not be closer to the traffic than 4 ft (1.2 m) or the edge of the treated shoulder, whichever is greater.

Curb/Guiderail Relationship. If curbs are used in conjunction with guiderail on roads having a design speed in excess of 40 mi/h (64 km/h), the face of curb should preferably be located either at or behind the face of guiderail. Under no conditions should the face of curb be located more than 9 in (0.23 m) in front of the face of rail. This restriction is necessary to prevent a vehicle from “vaulting” over the rail or strik­ing it too high to be contained. Although guiderail is not normally used on curbed roadways having design speeds of 40 mi/h (64 km/h) or less, the same criteria used for higher-speed roadways should apply. Where this is not feasible or practical, the curb may be placed in front of the rail. Regardless of the design speed of the roadway or the placement of the curb, the face of guiderail should not be located closer than 4 ft (1.2 m) to the roadway.

Curb Transitions. Curb and raised median beginnings and endings should be tapered from the curb height to 0 in (0 m) in 10 ft (3 m). When an urban-type section with curbs at the edge of pavement changes to a rural-type section without curbs, the curb should be transitioned laterally at a 4:1 (longitudinal:lateral) rate to the outside edge of the treated shoulder, or 3 ft (0.9 m), whichever is greater. When a curbed side road intersects a mainline that is not curbed, the curb should be terminated no closer to the mainline edge of pavement than 8 ft (2.4 m) or the edge of the treated shoulder of the mainline, whichever is greater.